Everything for your bathroom waterproofing: The Wakol Sealing System offers all...
Wakol offers a waterproofing system so that the water in bath and shower stays where it should and does not simply seep into the ground. All system component for waterproofing wet areas in domestic area (Class W1 and W2) under parquet and elastic flooring are perfectly compatible. Best conditions for your next project.
And that's how it works:
*Step 1 // Marking the areas for the application of adhesive on the wall and floor in 6 cm height and width.
*Step 2 // Apply WAKOL MS 552 PVC and Rubber Adhesive with trowel notch TKB B1 in the area of the inner and outer corners. Place and press on WAKOL AS 153 Sealing Corners, inner and WAKOL AS 154 Sealing Corners, outer. Flatten out surplus adhesive with a spatula.
*Step 3 // Cut WAKOL AS 152 Sealing Tape to length with approx. 5 cm overlap on sealing corners.
Apply WAKOL MS 552 PVC and Rubber Adhesive in the marked floor and wall area. Place and press on WAKOL AS 152 Sealing Tape. Flatten out surplus adhesive with spatula. Repeat the same procedure on the wall.
*Step 4 // Mark and cut the WAKOL AS 151 Sealing Sheet for floor and wall areas.
Apply WAKOL MS 552 PVC and Rubber Adhesive with trowel notch TKB B1 to the wall and allow to air dry for approx. 20 minutes to increase the initial adhesion. Apply WAKOL AS 151 Sealing Sheet and rub down bubble-free with a cork board.
Repeat the same procedure on the floor surfaces. Lay the sheets against each other, do not overlap, and rub down with a cork board until bubbles are eliminated.
*Step 5 // Apply WAKOL MS 552 PVC and Rubber Adhesive to the marked area left and right of the sealing sheets at sheet joints and allow to air dry for at least 20 minutes. Insert WAKOL AS 152 Sealing Tape and press on bubble-free. Flatten out surplus adhesive with spatula.
*Step 6 // Apply WAKOL MS 552 PVC and Rubber Adhesive in the area of installation openings on the wall and allow to air dry for at least 20 minutes. Insert sealing sleeves and press on bubble-free. Finally, remove any excess and leaking adhesive with the spatula.
Mission "Seal your bathroom" is completed: Water march - with the Wakol Sealing System!
Please always observe the technical information before processing.
All system components can be found at https://www.wakol.com/en/laying-material/products/underlays-mats-tiles
The processing instructions with all steps can be found here as a PDF file.
Do you have any questions?
For technical support please contact your responsible sales representative or the Wakol technical service, phone: +49 6331 8001-187.
Wakol presents the new products 2020...
Wakol presents the product news for the second half of 2020 in a compact flyer.
Work cleanly with the dust-reduced levelling compounds WAKOL Z 610 Levelling Compound, dust-reduced , WAKOL Z 680 Levelling Compound, dust-reduced and WAKOL Z 615 Levelling Compound, dust-reduced from Wakol. Just no dust-reduced levelling compound at hand? The WAKOL Dust Reducer helps to mix conventional WAKOL levelling compounds in a dust-reduced way.
Which of the 1-component parquet adhesives from Wakol are shear resistant? WAKOL MS 290
Parquet Adhesive, shear-resistant
, WAKOL MS 292 Parquet Adhesive, shear-resistant
and WAKOL PU 385 Parquet Adhesive, shear-resistant
! The product names have been amended for better differentiation.
Low-odour carpet adhesive pleasing? The low-odour carpet adhesive marked with the Blue Angel now bears this characteristic in its name: WAKOL D 3310 Carpet Adhesive, low-odour
Do you have further questions about the products? Our technical support team is available for technical service under +49 6331 / 8001-187.
Product news flyer 2020 for download .
The processing video of WAKOL PU 280 Polyurethane Primer is now available on Youtube ...
The new video of WAKOL PU 280 Polyurethane Primer
is now available.
In the step-by-step instructions you can see the subfloor preparation with WAKOL PU 280 Polyurethane Primer. How to continue working on the dried primer? Either direct adhesion with WAKOL MS Adhesives or the use of WAKOL D 3045 Special Primer before the following levelling.
The ready-to-use polyurethane primer guarantees a permanent barrier against capillary moisture in two work coats.
And further processing is possible just 40 to 50 minutes after application.
In other words, the floor covering can be laid the same day.
Blocking residual moisture on cement screed and concrete quickly and safely - without prior moisture measurement?
This is possible with the proven WAKOL PU 280 Polyurethane Primer.
The new WAKOL Product Line Laying Materials 2020 is available – including extended ordering information …
With immediate effect the new WAKOL Product line Laying Materials 2020 is available. To facilitate ordering, the product descriptions now not only include information about packaging units and container sizes but also indicate how many containers are fitted to a pallet.
As usual, the products are categorized by flooring type to enable parquet and floor layers to quickly find the right solution. If a product is suitable for the laying of different types of flooring, it will be listed in all of these categories.
Last but not least, application instructions exist for the direct installation of elastic and textile floorings respectively parquet on standardised or renovated subfloor as well as the subfloor preparation of non-suitable subfloors for direct bonding of elastic and textile flooring respectively parquet.
The categories in the product line as well as in the internet are following:
As the spread of the disease continues...
Given the fact, that the coronavirus COVID-19 spreads rapidly around the globe, protecting our employees, our customers, our business partners and suppliers is our highest priority.
At the same time, we have taken measures to sustain our ability to deliver.
All employees work from home respectively in shifts, while keeping a safe distance.
From purchase through production, technical service and sales up to shipping: we are fully committed to sustain our ability to deliver.
The Wakol sales force is available for you too!
If you need support or have any questions:
You can reach your contact person as usual via phone and E-Mail.
Stay safe and healthy during these tough times!
At LATAMCAN, Wakol presents its comprehensive Sealing Compound product line...
Wakol, leading provider of adhesives and compounds, exhibits at LATAMCAN 2020 in Sao Paolo, Brasil. From March 4 to 6, the technical conference facilitates the exchange of experience between the packaging industry and their suppliers.
Sealing Compounds from Wakol make the difference – whether the cover geometry is round, oval or square, whether manufacturers work in ultra-efficient in-line processes or are organised in separated work stations. The high-performance product range is destined for food and beverage packaging as well as technical goods.
A broad technological expertise, with know-how reaching beyond sealing compounds, forms the foundation for the sophisticated product systems. Wakol’s technical team is also keeping an eye on the regulatory environment, when it comes to food packaging. Customers can always expect a safe application in economical and energy-efficient processes.
At LATAMCAN, the Wakol exhibition team is looking forward to inform you about the full product range and will be available for further details.
For more information about LATAMCAN: www.latamcan.com
From January 22 to 25, Wakol introduces at CASA three additions to its Laying Materials product portfolio, enabling parquet and floor layers to stand out by their excellence in craftsmanship.
Sealing screed joints firmly without sanding? Installing vinyl flooring tiles firmly on walls? Just one powerful adhesive for installing a wide range of parquet flooring types?
At CASA trade fair, Wakol presents its powerful range of Laying Materials alongside with floor finishing products from Loba in exhibition hall 10, stand 537. Visitors can benefit from hands-on demonstrations of the new products – WAKOL MS 315 Cast Resin, WAKOL MS 262 Parquet Adhesive, firm-elastic and WAKOL MS 552 PVC and Rubber Adhesive.
WAKOL MS 315 Gießharz – powerful and precise
Especially developed for repairing screed cracks and for the force-locked sealing of screed joints is the new WAKOL MS 315 Cast Resin . Based on state-of-the-art and solvent-free MS technology it is suitable for all types of screed inclusive mastic asphalt.
Good news for parquet and floor layers: the 1-component cast resin is ready to use after only one minute. Just fill the required quantity of water into the bottle, using the measuring scale on the cap. Then shake the bottle well.
Moreover, when applying WAKOL MS Cast Resin on the subfloor, sanding and removing of surplus sand is no longer necessary. This saves both time and work material. Screed cracks can be repaired without any interruptions. And after hardening, the subfloor can directly be primed with all compatible Wakol primers.
In addition, WAKOL MS 315 Cast Resin enables the bonding of metal profiles, artificial or natural stone – indoors and outdoors. On top, it is not sensitive to freezing and comes conveniently packaged in a box with 6 bottles including 20 metal anchors per bottle.
WAKOL MS 552 PVC and Rubber Adhesive – the non-slip LVT tile adhesive
Using PVC tiles as a decorative interior wall covering is becoming increasingly popular. Accordingly, Wakol has extended its product range with the new WAKOL MS 552 PVC and Rubber Adhesive .
The silan-based adhesive comes with structure viscous properties, tailored to the specific requirements of wall tile installations. As a result, WAKOL MS 552 PVC and Rubber Adhesive is easy to spread, while applying it to wall surfaces. Afterwards, it enables a non-slip bonding to ensure that the PVC tiles stay exactly in the desired position on the wall. With that, a visually appealing and technically perfect result is guaranteed.
The 1-component adhesive is suitable for laying PVC tiles to absorbent and non-absorbent substrates, even in damp areas. Thus, WAKOL MS 552 PVC and Rubber Adhesive also allows for a fast and easy kitchen or bathroom makeover. Regarding consumer protection, it is classified as „very low emissions“.
WAKOL MS 262 Parquet Adhesive, firm-elastic – now available in 18 kg buckets
Thanks to high inner strength and high suction adhesion WAKOL MS 262 Parquet Adhesive, firm-elastic is a reliable partner for laying parquet flooring. The silan-based adhesive enables to safely absorb any movement caused by expansion. Moreover, parquet flooring laid with firm-elastic adhesive has a smoother surface than flooring laid using standard elastic adhesive.
From now on Wakol offers the 1-component adhesive not only in the convenient sausage packaging, but also in a sealed 18 kg bucket. WAKOL MS 262 Parquet Adhesive, firm-elastic is suitable for for laying mosaic parquet, on edge lamella parquet, strip parquet, multi-layer parquet, solid wood planks as well as cork flooring with an HDF / MDF middle layer and cork stabilising layer on absorbent and non-absorbent subfloors indoors. Regarding consumer protection, it is also classified as „very low emissions“.
Further product information can be obtained during the hands-on product demonstrations at the Wakol stand. Presentations will be given several times per day in exhibition hall 10 / 537. We look forward to meeting you!
Please find the official press release HERE .
From 10 to 13 January, Wakol presents the latest additions to the product range in hall 13, stand C22: WAKOL MS 315 Cast Resin, MS 262 Parquet Adhesive, firm-elastic as well as WAKOL MS 552 PVC- and Rubber Adhesive. Look forward for daily demonstrations.
WAKOL MS 315 Cast Resin – powerful and precise
A perfectly laid floor requires a professional subfloor preparation. Especially developed for repairing screed cracks and for the force-locked sealing of screed joints is the new WAKOL MS 315 Cast Resin . Based on state-of-the-art MS technology it is suitable for all types of screed inclusive mastic asphalt.
The reactive cast resin allows for fast mixing and can be applied directly without sand broadcast with all compatible Wakol Laying Materials, which makes it easy to use for floor and parquet layers. In addition, WAKOL MS 315 Cast Resin enables the bonding of metal profiles, artificial or natural stone – indoors and outdoors. On top, it is not sensitive to freezing and comes conveniently packaged in a box with 6 bottles including 20 metal anchors per bottle.
WAKOL MS 262 Parquet Adhesive, firm-elastic – now available in 18 kg buckets
Thanks to high inner strength and high suction adhesion, WAKOL MS 262 Parquet Adhesive, firm-elastic is a reliable partner for laying parquet flooring. The reactive MS adhesive enables to safely absorb any movement caused by expansion. Moreover, parquet flooring laid with firm-elastic adhesive has a smoother surface than flooring laid using standard elastic adhesive.
Right on time at the start of the new year Wakol offers the 1-component adhesive not only in the convenient sausage packaging, but also in a sealed 18 kg bucket. WAKOL MS 262 Parquet Adhesive, firm-elastic is suitable for for laying mosaic parquet, on edge lamella parquet, strip parquet, multi-layer parquet, solid wood planks as well as cork flooring with an HDF / MDF middle layer and cork stabilising layer on absorbent and non-absorbent subfloors indoors.
Due to its structure viscous properties it allows for easy spreading while enabling a non-slip bonding of the parquet flooring.
WAKOL MS 552 PVC- and Rubber Adhesive – the non-slip wall tile adhesive
Using PVC tiles as a decorative interior wall cladding is becoming increasingly popular. Accordingly, Wakol has extended its product range with the new WAKOL MS 552 PVC- and Rubber Adhesive . The structure viscous adhesive ensures that the PVC tiles stay exactly in the desired position on the wall and therefore enables a non-slip bonding. A visually appealing and technically perfect result is guaranteed. The 1-component MS adhesive is suitable for laying PVC tiles to absorbent and non-absorbent substrates.
With that, the three Wakol product innovations enable floor and parquet layers to work efficiently and stand out by their quality craftmanship. Regarding consumer protection, WAKOL MS 315 Cast Resin, WAKOL MS 262 Parquet Adhesive, firm-elastic and WAKOL MS 552 PVC- and Rubber Adhesive are all classified as „very low emissions“.
Further product information can be obtained during the hands-on product demonstrations at the joint stand of Loba and Wakol. Presentations will be given every full hour in exhibition hall 13, stand C22. We look forward to meeting you!
Please find the official press release HERE .
You will find us at following fairs ...
Interesting news are awaiting you!
More information will follow soon.
More information will follow soon.
Hall 3, Booth 3A34
More information will follow soon.
We are looking forward to meet you there.
For further information please contact us: Telephone: +49 6331 8001 131, E-Mail: Info@wakol.de
Wakol presents the new products 2019...
Wakol presents the product news for the second half of 2019 combined on one flyer. Check out the latest additions to the category “Preparing”: WAKOL MS 315 Cast Resin which comes with excellent adhesion properties on various materials and WAKOL MS Special Roller . WAKOL Z 625 Levelling Compound characterized by very fast readiness for covering was launched in the product category “Levelling”.
New under “Bonding Parquet / Cork Floorings” is WAKOL D 1690 Parquet Adhesive – advantages include high suction adhesion (similar to MS adhesives) as well as excellent ridge formation. Last but not least, Wakol offers a new polyester fibre sheet for decoupling and soundproofing reduction: WAKOL RP 704 Project Decoupling Sheet, 4 mm , available under “Underlays / Mats / Tiles”.
All in all, Wakol offers a refined and comprehensive product system with high demands for quality enabling parquet and floor layers to stand out by virtue of their skill and expertise.
In case of any questions: Our technical support team is available for technical consultation under +49 6331 / 8001-187.
Products news flyer 2019 for download .
Alternatives to water-based CR adhesives and more ...
Driven by increasing technology requirements and changes in the supply of raw materials, Wakol is continuously expanding its foam adhesive product line. Accordingly, product launches at interzum 2019 include Chloroprene-Rubber(CR)-free water-based spray adhesives as well as an innovative flame retardant CR-Latex adhesive.
The demand for alternatives to water-based CR adhesives is higher than ever. Tailored to meet market requirements, Wakol has developed INTERCOLL D 3095, a CR-free 2-C dispersion adhesive based on polyurethane suitable for the manufacturing of mattresses and upholstery. Product features are comparable to 2-C CR-Latex adhesives. INTERCOLL D 3095 shows high initial tack as well as excellent green strength for bonding foam materials in a very short time. The dried adhesive film is very flexible and resistant against ageing. Moreover, INTERCOLL D 3095 is free from chlorine respectively halogen-organic compounds in general.
The new INTERCOLL D 3468 is a solvent-free 1-C CR-Latex adhesive that produces a self-extinguishing adhesive film and is therefore suitable for use in components that have to comply with fire protection requirements. Application fields include seating components designed for public transport respectively mass transport as well as mattresses for cruise ships or military facilities. From a product feature perspective, INTERCOLL D 3468 shows high temperature stability as well as excellent green strength for bonding foam materials in a very short time.
Visit Wakol at interzum from May 21st - 24th 2019 in in Hall 10.1, Aisle H, Stand 011 and convince yourself of the INTERCOLL-Products .
Visit Wakol in hall 10.1, stand H 11
INTERCOLL D 3442 is a multi-purpose contact adhesive especially developed for the manufacturing of sandwich mattresses and spring mattresses with high tension. The water-based 1-C CR-Latex roller adhesive is solvent-free and odor-optimized, enabling a good workplace hygiene. Process reliability, production efficiency and product quality are featured by a very quick initial tack and a quick force build-up. Tensions in the glue line are reliably maintained. INTERCOLL D 3442 is suitable for all common application methods used for the assembly of mattresses, including double rollers as well as low pressure spray guns.
INTERCOLL D 3470 is a high-performance spray adhesive that displaysa very fast initial tack even at very low spray pressures. The water-based polychloroprene latex adhesive bonds all typical upholstery materials, such as foam materials, non-woven materials, upholstery fabrics, wood, hard fibre or cardboard. Due to its special formulation, INTERCOLL D 3470 suppresses the formation of fine spray mist. This leads to more efficient use of the adhesive thanks to greater transfer efficiency with the spray application and less overspray. As a result, up to 10 % increase in productivity is achieved. Moreover, workstation and surrounding area are significantly less contaminated.
Visit Wakol at interzum from May 21st - 24th 2019 in in Hall 10.1, Aisle H, Stand 011 and convince yourself of the INTERCOLL-Products .
Product demonstrations will be given several times a day directly at the stand of Wakol.
We look foward to meeting you!
Further information can be obtained on www.interzum.com .
Wakol and Ardex Australia announced today, they have jointly acquired a strategic majority stake in Nexus Adhesives.
Nexus Adhesives is a market leader in the flooring adhesive and carpet backing compound industry in Australia.
“This joint venture strengthens our leading position in the Australian market,” said Mark Eslamlooy, CEO ARDEX Group. “With our system competence we provide solutions for our customers.”
“We feel very proud that ARDEX and Wakol have asked Nexus Adhesives to join the group,” Jonathon Clewlow and Brett Nixon said, Owners of Nexus Adhesives. “It’s a vote of confidence in Australian manufacturing and we look forward to exploring growth opportunities for Nexus Adhesives both in Australia and further afield.”
Nexus will continue to operate independently from the ARDEX companies. Jonathon Clewlow and Brett Nixon will continue to manage and drive Nexus Adhesives forward.
Established in Australia in 2006, Nexus Adhesives manufactures and distributes flooring adhesives and carpet backing compounds throughout Australia and New Zealand. Dedicated to delivering innovative, dependable products, they focus on servicing the professional contractor.
WAKOL PU 280 Polyurethane Primer has already proven its worth as a fast and efficient moisture barrier on more than 20 million square meters. Now it is officially confirmed that the moistuere barrier is applicable on unheated cement screeds and concrete even without previous moisture measurement.
Continuous practical experience and the results of additional test cycles have shown: WAKOL PU 280 Polyurethane Primer has achieved a new level of product quality. According to the extended recommendation it enables blocking of capillary moisture in unheated cement screeds and concrete in two layers – even without previous moisture measurement.
Extended recommendation underlines proven performance
„The performance and reliability of WAKOL PU 280 Polyurethane Primer is continuously being tested by our product specialists”, says Birgit Hansen, Head of Marketing and Customer Service Center at Wakol. “The results have convinced us to officially update the recommendation of use."
Reliable and fast residual moisture barrier
As a one-component product WAKOL PU 280 Polyurethane Primer is always ready for immediate use. Mixing errors and disposal of residual amounts are a thing of the past. With 40 to 50 minutes drying time per application, work may directly continue the same day.
Further information about WAKOL PU 280 Polyurethane Primer as well as the entire Wakol product portfolio can be obtained under www.wakol.com/en/Laying-Material/Products. Please find the official press release HERE .
Michael Fischer confirmed as Managing Partner, further expansion and long-term succession secured...
Adhesives manufacturer Wakol GmbH is increasing its share in LOBA GmbH & Co. KG, one of the world’s leading manufacturers of surface treatments, and now holds a majority stake in the company. As Wakol has been majority-owned by ARDEX since 2015, LOBA will thus become part of the international ARDEX Group. To facilitate this transaction, four long-standing LOBA shareholders have put their shares up for sale. The overriding goal of this decision is to safeguard the company’s long-term success. Therefore, the new shareholder structure consists of Wakol GmbH and Michael Fischer, who will remain as Managing Partner.
“By linking LOBA with Wakol, we have managed to provide our company with an extremely sustainable perspective and pave the way for my succession early on. The international operations of the ARDEX Group offer excellent opportunities to continue growing and to lead LOBA into a successful future”, says Managing Partner Michael Fischer about the new structure. “I am most delighted that our shareholders unanimously supported this step and that we have been able to win such substantial partners for LOBA”.
Christian Groß, Wakol shareholder and CEO, sees the strengthening and expansion of the existing cooperation as a common goal: “LOBA and Wakol have been working together excellently for over 20 years and we are now able to reinforce this even further. I am convinced that the ARDEX Group offers great opportunities for both companies, whilst at the same time preserving the values and culture of a family business”.
Mark Eslamlooy, CEO of the ARDEX Group, has also expressed his pleasure over the partnership: “The cooperation with LOBA provides us with an optimal constellation to further expand our competence in the field of flooring systems and surface finishings. The LOBA brand enjoys a distinguished reputation and stands for technical competence, premium products and outstanding service. The strong international orientation and the extremely high level of commitment of the people involved have convinced us that LOBA is the ideal partner for us”.
Ditzingen site to be expanded – company will remain independent
LOBA's Ditzingen site will be further expanded as a development and production center for surface finishing within the ARDEX Group. The treatment and finishing of wood and cork currently play a key role for LOBA. Additionally, the company is expanding its activities in finishing resilient floor coverings as well as cementitious surfaces.
The company name, brand and sales structure remain unchanged as well as the contact persons for customers and suppliers. In both companies, the organization and personnel will remain the same. Following a mandatory review by the antitrust authorities, the transaction is expected to be completed at the latest by the end of November 2018.
Wakol GmbH develops, produces and very successfully sells laying materials, industrial adhesives and sealing compounds. It has stood for premium quality and customer accessibility for over 80 years. The ARDEX Group has been the majority shareholder of this family-owned company since 2015. Over 185 people are employed at the headquarters in Pirmasens; worldwide, the Wakol Group employs around 230 people. Besides Germany, Austria, Switzerland, North America and the Netherlands are amongst the most important sales markets. There are further intensive activities in Poland, Italy and Great Britain, to name a few. Wakol is also actively involved in global exports.
Founded in 1922, the finishing and care of parquet and hardwood floors have been the core business of the company based in Ditzingen near Stuttgart for almost 100 years. LOBA also owns subsidiaries in Brazil and China, as well as joint ventures with Wakol in Poland and North America. The LOBA Group currently employs around 120 people, 97 of whom work at the Ditzingen site. Technical excellence, top-quality products and the extremely well-focused customer orientation are the key factors for the success of the LOBA brand in over 60 countries.
ARDEX GmbH is one of the world’s market leaders in high-quality chemical building products. As a family-owned company, the company has maintained a sustainable growth course for over 65 years. Today, the ARDEX Group employs more than 3,000 people and is represented in over 100 countries on all continents, boasting a virtually end-to-end presence in its core market of Europe. With more than ten major brands, including Wakol, ARDEX generates total turnover of over EUR 770m worldwide.
We updated our privacy statement...
We, Wakol GmbH, Bottenbacher Str. 30, 66954 Pirmasens, would like to inform you in detail about the processing of your personal data (hereinafter referred to as "data") in accordance with Article 13 of the EU General Data Protection Regulation (EU GDPR). The EU GDPR places some useful and meaningful obligations on us in order to ensure the protection of your data during processing. We are happy to fulfil these obligations. In the following we shall explain which data we process about you and for which purposes and the rights you have in this regard.
Purposes of processing
The processing of your data is required for the execution of contractual services and/or the performance of pre-contractual services.
We process your data for the following purposes:
• Your address data for the fulfilment of pre-contractual services
- Initiation of contractual performance
- Payment guarantee
• Your address, payment and turnover data based on the contract concluded with you for:
- Performance of contractual service
- Payment processing
- Supply of contractually ordered products and services
• Your data shall not be transferred to third parties, except
Address data to logistics companies for the delivery of the goods
- Account details to banks for payment processing
- Address details to credit agencies for payment guarantee
- Address and reminder data to credit insurers for payment guarantee
- Address, payment and turnover data to legal representatives, insurance companies and courts for reminders, debt collection and disputes
- Address, payment and turnover data to tax consultants, auditors and accountants, financial and administrative authorities insofar as it is required for the performance of their tasks.
• IT service providers may obtain a potential insight into the stored data within the framework of providing support.
• Based on the consent you have given
- Mailing of interesting information about products and campaigns, training and trade fairs and exhibitions of Wakol and its affiliated companies..
Period of processing
We shall only process your data for as long as is required for the fulfilment of our contract or applicable statutory regulations as well as the maintenance of our relationship.
Business documents are stored for a maximum period of 6 and 10 years according to the German Commercial Code and the Fiscal Code.
As long as you do not object, we shall use your data for maintaining and intensifying our trust-based business relationships to our mutual advantage.
If you request the deletion of your data, we shall delete your data with immediate effect insofar as the deletion does not conflict with any legal retention requirements.
Your rights as an affected individual
In accordance with the EU GDPR, you have the right to:
Information about the processing of your data
• Correction or deletion of your data
• Restriction of processing (only storage is still possible)
• Objection to processing
• Data portability
• Revocation of your consent with effect for the future
• File a complaint with the data protection regulatory body. Your competent regulatory body is that located in your place of residence. A list of the regulatory bodies can be found here: http://www.bfdi.bund.de/DE/Infothek/Anschriften_Links/anschriften_links-node.html
We hope this information helps you in exercising your rights. If you require further information about the data protection regulations, please read our privacy statement or ask your regulatory authority.
Our Data Protection Officer , Mr. Ralf Nicklich, email@example.com is also available to answer any questions you may have with regard to data protection.
Costumers are able to catch up on all products, which are offered by Wakol. The product line is divided into the categories:
As you can see: Wakol offers a huge product variety in laying materials for the parquet and flooring laying crafts.
Product Line Laying Materials 2018 as download .
WAKOL D 3465 Special Adhesive
The presence of chromium (VI) compounds in leather and textiles is still one of the most relevant risks with respect to product safety that processors are confronted with today. The risk potential of these compounds is caused on the one hand by the intensive sensitising and contact allergen effect, and on the other hand in the case of chromium (VI) compounds carcinogenic effects are probable for people upon intake via the respiratory tract. This pronounced risk potential has led to an intensive occupation with the analysis of chromium (VI) and the legislation on the introduction of strict limit values. Since 2010 the German Consumer Goods Ordinance, for instance, has been stipulating that no chromium (VI) must be detectable in leather products with which not only passing physical contact is likely. A value of 3 mg/kg applies here as a detection limit. Since 2015 this limit value was also put into effect at European legislative level. Subsequently numerous retailers also included restrictions in their suppliers terms and conditions, some with even lower limits.
Although the topic has somewhat disappeared in recent years after intermittent intensive reporting also in the mass media, it still leads to recalls in the footwear industry as a result of non-marketable products that do not comply with the applicable limit values.
A key problem in the risk management of the topic is that with the exclusion of the chromium (VI) content an exit control does not represent adequate prevention for the safety of the finished products for the tanner. This is due to the fact that measurable and thus potentially alarming amounts of chromium (VI) may form during storage and further processing due to oxidative processes and the chromium (III) content from the tanning process. This chemical conversion is supported by a range of influencing factors.
This chemical conversion is inhibited by the following influencing factors:
Precise pH value control is therefore required. The negative influence of ammonia is particularly pronounced. Its use should therefore be avoided.
The last point in particular is perfectly understandable from a chemical perspective as the formation balance is moving more and more towards chromium (VI) in the alkaline range. As a result, adhesives were targeted during the examination of influencing factors as with classic natural latex adhesives there is a high pH value and significant amounts of ammonia. Studies by the Pirmasens-based PFI in 2011 within the framework of an IGF research project actually suggested a negative, albeit small, influence of the adhesives [IGF research project no. 15845 N (2011)]. Wakol addressed the issue with current development work and developed the alkali- and ammonia-free adhesive WAKOL D 3465 Special Adhesive. Owing to the near neutral pH value of approx. 7.5 a significant reduction of the risk of adhesive-related formation of chromium (VI) can be expected. In this way with the use of a neutral adhesive the processor can avoid additional risks in the processing chain in situations where the tannery does not comply with "Best Practice" with regard to chromium (VI) prevention.
Bottenbacher Straße 30
Innovative bonding of shafts
Wakol offers a new sprayable shoe adhesive with high initial strength and excellent processing properties. WAKOL D 3465 Special Adhesive is suitable for the manufacture of shoe shafts and insoles by hiding all common leather, cushioning and lining materials.
The use of this alkali- and ammonia-free raw material with very low allergenic potential reduces the skin-irritating effect of the adhesive significantly or substantially. Contamination of the adhesive during processing is impossible with the application in the closed container. Only a 10 kg container is connected directly to the spray gun which avoids the former refilling into a pressurised container. Mould formation in pressurised containers is therefore impossible.
The absence of odours (no ammonia) during processing is particularly beneficial. A high initial strength is already achieved with little pressure. In order to control the spray application of the undyed adhesive also on bright lining materials, a UV indicator is added which enables visualisation under black light. Typical spray devices can be used without any problems. Only the selected spray pressure must be readjusted or reduced to 1-2 bar. It is possible to clean the application devices with water. Work benches can also be easily cleaned with little effort. Very high heat resistance allows other work processes such as heatsetter, blow-drying and steaming without any problems. Hydrolysis tests (70°, 7d , 100% RF) permit use in the area of heavy and sports footwear.
Bottenbacher Straße 30
Wakol can also be found now on...
Besides that the follower on @Wakol.Verlegewerkstoffe will be informed about upcoming appointments, workshops or fair participation.
Visit us on our new Facebook page!
We’re looking forward to your active participation, your likes, comments and ideas! Your opinion is important to us.
WAKOL presents it's newest products at Domotex 2018
Everyday life on the contstruction site presents us with new challenges – the new products of Wakol are the key to your success. The start in an ergonomic and economic year is ensured with Wakol.
With the rollable WAKOL MS 325 Silane Primer you are optimal prepared at lightning speed. The versatile usage for subfloor preparation and the very low hardening time of 3 - 4 hours allows you to continue working on the same day.
Strike with no effort at all with the new WAKOL MS 292 Parquet Adhesive – fast, clean and comfortable. The exceptionally high suction adhesion, the small consumption and the ergonomic application of the adhesive in stand, are a big award to this product.
Laying LVT in areas with increased moisture? With WAKOL MS 550 PVC and Rubber Adhesive a safe and fast adhering is guaranteed. The very squeezing tendency is minimized and the subfloor can be used quickly.
Convince yourself! Together with Loba, we present our products in 2018 at Domotex in Hannover and show you how you can start with “Connected Systems” without effort and powerful into the new year.
You find Wakol in Hall 13, Stand B23
We are looking foward to your visit!
Further information on Wakol at DOMOTEX www.domotex.de
Wakol presents adhesive systems for manufacturing upholstery and mattresses
On the upcoming interzum 2017 in Cologne, Wakol presents adhesive systems for manufacturing upholstery and mattresses.
INTERCOLL D 3447 Roller Adhesive – is a diverse mattress adhesive for the manufacture of all types of mattresses. The water-based 1-C CR-Latex Roller adhesive is solvent-free and characterized by its superb tension stability when wet. The easy assembly and the process reliability are featured by the quick force build-up and the excellent instant tack.
INTERCOLL D 3386 – has been developed for roller and spray application. The very fast drying of the adhesive makes a directly packaging of the mattress possible. It can be used as one-side or contact adhesive for all common mattresses and upholstery materials.
During interzum 2017 Wakol presents live two spray applications:
The 2-C CR-Latex Dispersion Adhesive INTERCOLL D 3453 is used in combination with INTERCOLL D 3437 Aktivator by spray-mix-application. It shows high initial strength for bonding foam materials in a short time.
INTERCOLL D 3460 is a 1-C CR-Latex Dispersion Adhesive can be used at a low spraying pressure, thus reducing the overspray and optimising consumption. The product can be applied using the "free-flow" method. In comparison to the mixed two-component adhesive, INTERCOLL D 3460 contains more solid material and therefore has a lower water content. This adds a drying benefit.
Further information on Wakol at interzum www.interzum.de
WAKOL Sealing Compounds – expanded product range
Wakol presents at Metpack two new additions to its extensive Sealing Compound range.
- WAKOL D 3756 Sealing Compound for Beverage cans
- WAKOL PU 4320 / 4315 Sealing Compound for Food pails and drums.
WAKOL D 3756 Sealing Compound for Beverage cans
WAKOL D 3756 Sealing Compound is a water-based sealing compound based on SBR for beverage application and is suitable for the filling of mineral water, carbonated soft drink, beer as well as dairy products. It shows a very good performance using high throughput application machinery (up to 1500 epm / rotational multi-head liner) applying to small diameters.
It is formulated to achieve virtually no taste or odour influences on filling goods. Therefore WAKOL D 3756 Sealing Compound is suitable for taste-sensitive filling goods like e.g. mineral water.
It complies with latest regulatory requirements, according to European and FDA food contact regulations. TNO and Nehring certificates are available
It shows excellent performance on high-speed rotational multi liners due to low drying tendency on nozzles. Reject rates are exceptionally low. An excellent shear stability provides optimum performance through central supply systems.
WAKOL PU 4320 / 4315 Sealing Compound for Food pails and drums
WAKOL PU 4320 / 4315 Sealing Compound is a two-component, self-blowing polyurethane foam. It was especially developed to form gaskets for pails and drum covers with ring ladge application. For the product, full compliance for food contact according to European Food Contact law has been achieved.
As the foam shows a very good resistance against water, fats, oils and aliphatic solvents it can also be used for the sealing of packaging of aqueous-based products for technical applications, glycols, oils, aliphatic solvents and solid filling materials.
The reaction leads to an elastic and fine-porous gasket with a smooth surface. 2-C-Polyurethane technology offers several advantages: no oven needed, high form stability of the gasket, plasticizer free, low migration, PVC free.
The Wakol exhibition team is looking forward to inform you about the full product range and will be available for further details. Visit Wakol in Hall 3.0 Stand 3A34.
Further information on Wakol at METPACK www.metpack.de
Wakol participates at innovations@domotex2017 and will be presented with two products.
Wakol presents innovative products during DOMOTEX 2017 from 14th till 17th january in Hannover. The products will be shown at innovations@domotex2017 as well as on Wakol's stand in Hall 7 Booth A41 .
WAKOL MS 325 Silane Primer - the first roll- and spreadable MS Moisture Barrier with strengthening effect
WAKOL MS 550 PVC and Rubber Adhesive - the first 1-C MS adhesive for LVT Floorings.
innovations@Domotex2017 presents innovative products the online as well as during the fair show in hall 9.
Application and laying technologies Innovative exhibitors at DOMOTEX 2017 are demonstrating how the latest-generation technologies enable floor coverings to be laid more quickly and straightforwardly. "We have seen some exciting products that stand out thanks to creative and smart approaches. ..." explains Stefan Diez , Jury Chairman and Product and industrial designer.
You will find us at following fairs ...
Interesting news are awaiting you!
12.-15. January 2018
24.-27. January 2018
We are looking forward to meet you there.
For further information please contact us: Telephone: +49 6331 8001 131, E-Mail: Info@wakol.de
With Wakol a powerful appearance and optimal preparation at lightning speed! Wakol presented at DOMOTEX 2016 innovative new products
Wakol presents with WAKOL MS 325 Silane Primer the first roll-out MS Moisture Barrier with strengthening effect and with WAKOL MS 550 PVC and Rubber Adhesive the first MS based Adhesive for LVT Flooring. The practical demonstration of these ideal products for the next job site took place in hall 7, booth A43. Wakol presented their work to an interested audience.
WAKOL MS 325 Silane Primer - Optimal preparation at lightning speed!
For the first time it is possible to prepare the subfloor in just one application with an MS-based roll-on moisture barrier. The special WAKOL MS Special Roller guarantees efficient work and enables to apply the required amount of 250 g/m² as a moisture barrier. After only 3 to 4 hours drying time it is possible to continue with the next step, Regardless if you are laying parquet or subsequently applying levelling compound. This saves you additional trips to the job site.
WAKOL MS 325 Silane Primer is suitable for different types of subfloor preparation, as primer, strengthening agent for subfloors or as moisture barrier. The product can be used as a primer on new and old subfloors, firmly fixed adhesive residues, absorbent and non-absorbent subfloors. Worn out screeds are strengthened with WAKOL MS 325 Silane Primer. Increased residual moisture can be reliably and quickly blocked up to max. 4 CM% in unheated cement subfloors or up to max. 3 CM% in cement subfloors with integrated underfloor heating. There is a variety of possibilities available after applying the WAKOL MS 325 Silane Primer. You can either lay parquet directly on the primer using all admitted Wakol MS and PU parquet adhesives or lay textile or resilient flooring after an initial coating with WAKOL D 3045 Special Primer and subsequent levelling with WAKOL Levelling Compound. When time is of the essence and you want to lay the flooring on the same day, reach for WAKOL Z 715 Quick Setting Levelling Compound.
WAKOL MS 550 PVC and Rubber Adhesive – Powerful appearance!
Wakol presents the first MS adhesive for LVT flooring. The modern reaction adhesive for resilient flooring it is possible for the first time to securely install critical flooring with a 1-component MS adhesive which previously had to be done with 2-component PU adhesives. WAKOL MS 550 PVC and Rubber Adhesive is suitable for installing all PVC flooring, as well as LVT and rubber flooring. It doesn't matter whether you want to lay flooring on absorbent or non-absorbent subfloors, indoors or outdoors.
With no time-consuming mixing involved, WAKOL MS 550 PVC and Rubber Adhesive can be applied directly from the bucket to the prepared subfloor.
WAKOL MS 550 PVC and Rubber Adhesive is characterised by its very low squeezing tendency. For unavoidable work on the flooring imprints in the surface are kept to a minimum. LVT flooring is held securely in place right from the start thanks to the high suction adhesion and initial tack. Owing to the firm adhesive grooves of WAKOL MS 550 PVC and Rubber Adhesive, residual indentations are kept to a minimum just as well as with a fibre-reinforced dispersion adhesive. Adhesive residues on the surface of the flooring can be removed completely whether fresh or hardened.
After covering the remaining adhesive and closing the container the adhesive can be used for subsequent installations.
Further information to the products can be obtained on the internet site wakol.de/en/Laying-Material/Product-Highlights by mobile phone via a QR code on the label.
Visitors at Domotex 2016 were able to see the new products for themselves. Together with Loba Wakol demonstrated which products are a must in 2016.
Further information on Wakol at DOMOTEX www.domotex.de
Wakol goes mobil ...
Pirmasens, December 2015
Find the relevant information easier online! This was the goal behind the new web page of Wakol which is online since mid of the year. The new mobile web page makes it possible to navigate easier with your smartphone
You are looking for the relevant information of a product? You will find the information really easy with the new full-text search.
Give it a try!
Wakol kindly invites to ...
Wakol invites our international partners for a meeting from February 19th till February 21st, 2018 in Pirmasens, Germany. You can find here a rough time schedule:
The meeting included following contents:
- Product Introduction
- Technical Training
We kindly ask you to use the registration form limited for 2 persons/company in ordner to confirm your attendance. The costs for board, lodging and shuttle service will be borne by Wakol. More information and details coming soon.
The completed form must be sent to firstname.lastname@example.org by November 1st, 2017 at the latest. The invitation and the registration form can be downloaded here .
We are looking forward to your visit on 19th of February!
Adhesive manufacturer WAKOL enters into strategic partnership with ARDEX Group which will ensure early company succession ...
Adhesive manufacturer WAKOL enters into strategic partnership with ARDEX Group which will ensure early company succession.
Ardex, specialist for building chemicals based in Witten, Germany acquires a majority interest in Wakol. Family owners who are currently active in the business continue to hold substantial shares.
With Ardex as partner Wakol strengthens its system expertise, its global footprint and therefore ensures a sustainable growth.
This cooperation holds big potential for for future growth for both companies.
Mark Eslamlooy, CEO of Ardex Group, is excited about the future together: “This cooperation with Wakol is a perfect way for us to increase our systems expertise in the flooring industry massively. I cannot imagine having a better partner because like Ardex Wakol stands for highest technical expertise, quality and innovation. This shared philosophy is the base for our future success.”
Wakol stays independent
Wakol continues to operate as independent entity. The current managing directors Christian Gross, Dr. Frederic Holzbaur, Dr. Martin Schäfer and Steffen Acker will continue to run the business. Company name, location, brand and sales strategy will not change. The point of contact for customers as well as suppliers will also stay the same.
Through this cooperation both companies will increase their expertise in the business segment flooring systems. Both brands will continue to focus on their existing distribution channels and invest in its further development. Also both companies will continue to offer their distinguished product portfolio under their own brand.
Wakols further business segments Industrial Adhesives and Sealing Compounds will also continue increase without change. The international network of the Ardex Group offers opportunities for growth there as well.
Christian Gross, CEO of the Wakol Group is convinced: „ With Ardex as partner we have a very promising prospective for the future and at the same time foster our culture as family owned business.“
Location in Pirmasens will be strengthened
Wakol’s current location in Pirmasens will be expanded to become Ardex’s development centre for flooring adhesives in Europe. It is also planned to expand Wakol’s existing manufacturing capacity into the Groups European production centre for flooring and industrial adhesives.
Base for a partnership are shared values like: quality, innovation, technical expertise, reliability as well as a clear strategic alignment. Strong similarities in the company culture are crucial prerequisites and guarantee the future success for the cooperation.
For more than 60 years, ARDEX has been the quality leader for an entire industry, offering excellent building chemicals with supreme processing reliability – the brand of choice for installers and wholesalers. ARDEX today is still an independent family-owned business. ARDEX is present in more than 50 countries around the world and has 2,200 employees. With its twelve major brands, the ARDEX Group generates total turnover worldwide of more than 540 million euros per year.
Wakol GmbH is a leading family owned business in the adhesive industry as well as in the packaging industry with a total turnover of 58 million Euros. In 2014 Wakol achieved a growth of 5.5%.
Wakol, headquartered in Pirmasens, Germany continuously increased the number of employees over the recent years to currently 190 employees. 160 of that are based in Pirmasens.
Besides Germany, Austria, Switzerland and the Netherlands which are core markets for Wakol’s flooring products Wakol is also active in USA and Poland.
Wakol develops, manufactures and distributes very successful Flooring products, industrial adhesives and sealing compounds. For 80 years Wakol stands for Quality and Customer service. Wakol was repeatedly able to develop industry changing innovations. The chosen markets and niches provide excellent opportunities for future growth.
We, Wakol GmbH, hereinafter referred to as Wakol, respect the privacy of every individual who visits our website. The protection of your personal data is very important to us. In the following we explain what data pertaining to you we collect and for what purpose we use it. You also find out how you can exercise your rights.
All changes to this privacy statement shall be published on our website. This allows you to obtain information at any time about the type of data we collect and how we use this data.
This privacy statement shall not apply to websites which can be called up via hyperlinks on our website.
1. Collection and processing of http protocol data
a. Name of responsible body: Wakol GmbH
b. Address of responsible body: Bottenbacher Str. 30, 66954 Pirmasens, Germany
When you visit our website and each time you retrieve a file, the web server collects protocol information about these processes (e.g. browser type, date and time of retrieval). This is not personal data. It is thus not possible for us to assign the collected data to a certain natural person.
We evaluate this data exclusively for statistical purposes. We shall not forward this data to third parties. We shall not link this data to other data. The data is also deleted regularly within one week after a statistical evaluation.
2. Use of personal data
Personal data shall only be collected by us if and to the extent of which you make available this data to us with your knowledge. In particular, this personal data shall only be used for the purposes of advertising/market research, as well as for the design of our services, if you have given us your express consent for this purpose.
You have the right to revoke your consent at any time.
Information about the processing purposes is provided at the corresponding places on our website and is not subject to a subsequent change.
The data shall only be forwarded to third parties without your consent if we are legally obliged to do so.
Cookies are data records that are sent by the web server to the web browser of the user and stored there for later retrieval. You decide whether cookies can be collected by setting your browser so that you are informed before a cookie is stored and the cookie is only stored if you expressly accept this setting.
Our cookies contain the following data records:
Name of the retrieved file
Date and time of the retrieval
Transmitted data volume
Message whether the retrieval was successful
The data records do not contain any personal information. This data shall not be merged with any personal data you provide. You can also prevent the collection of data generated by the cookie and related to your use of the website (incl. your IP address) by Google, as well as the processing of this data by Google, by downloading and installing the browser plug-in available under the following link. The current link is tools.google.com/dlpage/gaoptout.
4. Use of social media
Plug-ins from different social media networks are integrated in our website. The services are provided by the respective companies ("operators"). These operators are:
Facebook is operated by Facebook Inc., 1601 S. California Ave, Palo Alto, CA 94304, USA ("Facebook"). An overview of the Facebook plug-ins can be found here: https://developers.facebook.com/docs/plugins
Twitter is operated by Twitter Inc., 1355 Market St, Suite 900, San Francisco, CA 94103, USA ("Twitter"). An overview of the Twitter plug-ins can be found here: https://dev.twitter.com/web/tweet-button
LinkedIn is operated by LinkedIn Corporation, 2029 Stierlin Court, Mountain View, CA 94043, USA ("LinkedIn"). An overview of the LinkedIn plug-ins can be found here: https://developer.linkedin.com/plugins#
Xing is operated by XING SE, Dammtorstr. 30, 20354 Hamburg, Germany, Tel.: +49 40 419 131-0, E-mail: email@example.com. An overview of the Xing plug-ins can be found here: https://dev.xing.com/plugins.
Google+ is operated by Google Inc. (1600 Amphitheatre Parkway, Mountain View, CA 94043, USA). An overview of the Google+ plug-ins can be found here: https://developers.google.com/+/web/
YouTube is operated by YouTube LLC., 901 Cherry Ave., San Bruno, CA 94066, USA (“YouTube”). An overview of the YouTube plug-ins can be found here: https://developers.google.com/youtube/
In order to further protect your data when visiting our websites, these plug-ins are implemented as a "2-click solution". This type of integration ensures that you are not automatically connected to the servers of the provider when accessing a page on our website that contains such plug-ins. The browser shall only establish a direct connection to the servers of the operator if you activate the plug-ins, thus permitting the data transfer. The content of the various plug-ins shall be transferred by the respective operator directly to your browser and then displayed on your screen.
The plug-in informs the operator about which of our pages you accessed. If whilst visiting our website you are logged in to your user account with the respective operator, the operator may merge your interests, i.e. information which you access, with your user account. With the use of the plug-in functions (e.g. clicking on "Like" button, posting a comment), this information shall also be transferred from the browser directly to the operator for storage.
More information about the collection and use of data by the operator and about your rights and options for protecting your privacy can be found in the privacy statements of the operators:
Privacy Statement of Facebook: http://www.facebook.com/policy.php
Privacy Statement of Twitter: https://twitter.com/privacy
Privacy Statement of Xing: https://privacy.xing.com/de/datenschutzerklaerung
Privacy Statement of LinkedIn: https://www.linkedin.com/legal/Data Protection-policy
Privacy Statement of Google+: https://policies.google.com/privacy/update?hl=de
Privacy Statement of YouTube: https://policies.google.com/privacy/update?hl=de
5. Rights of parties affected:
5.1. Right to information
You have the right to obtain information at any time about the data stored about you, including the origin and recipients of your data, as well as the purpose of the data processing. Please send your request in writing or by e-mail to our addresses listed below.
This privacy statement shall only apply to the content of our servers and does not cover the websites linked on our site.
5.2. Right to complain to the data protection authorities
Irrespective of other administrative or legal remedies, you shall have the right to complain in accordance with § 24ff Data Protection Act 2018 to the data protection authorities if you believe that the processing of your data violates the GDPR.
The data protection authorities shall inform the complainant of the status and outcomes of the complaint including the possibility of a legal remedy.
6. About us
This is the privacy statement of Wakol GmbH, Bottenbacher Str. 30, 66954 Pirmasens, Germany.
Internet www.wakol.com; E-mail firstname.lastname@example.org
Should you have any questions about this privacy statement, please contact us directly by post or e-mail. Data Protection Officer: Ralf Nicklich, E-mail: Ralf.Nicklich@wakol.de
7. Updates and changes
Parts of the privacy statement may be modified or updated by us without informing you in advance thereof. Please check the privacy statement before you use our website in order to stay informed of any possible changes or updates. Privacy Statement as at: May 2018.
|Bottenbacher Straße 30|
|Phone +49 6331 8001 0|
|Telefax +49 6331 8001 890|
Christian Groß (CEO)
Dr. Martin Schäfer
|Data Protection Officer: Ralf Nicklich|
|Registration court Zweibrücken|
|Registration number HRB 22028|
|VAT-Ident-Nummer DE 149605817|
Liability note: Despite careful checking, we assume no liability for the content of external links. The operator is exclusively responsible for the contents of the interlinked sides.
Concepts and design: mono-dimension.com
Programming und realisation: infolox.de
Take exit Pirmasens/ Bitsch and turn left at the second traffic light (Winzeln/ Industriegebiet West). Continue straight ahead to Industriegebiet West. Then turn right at the roundabout towards A8/A62. Take the first exit towards Winzeln/Gersbach/Windsberg. After passing the village entrance, turn third right and you arrived at Wakol premises.
Take exit Winzeln/Industriegebiet West. Take the bypass L600 to Pirmasens-Winzeln. Then turn left to Winzeln and after that take the first street on the right site. After passing the village entrance, turn third right and you arrived at Wakol premises.
A 6 / B 270
Take the exit Kaiserslautern-West to B270 towards Pirmasens. Once you’ve passed the village entrance, make a right turn after the traffic light towards A8 (Zweibrücken). Take exit Winzeln in case of coming from A8. While driving on bypass L600 towards Pirmasens-Winzeln, turn left to Winzeln and then the first right. After passing the village entrance, turn third right and you arrived at Wakol premises.
From A8 towards Zweibrücken, take exit Winzeln/ Industriegebiet towards Pirmasens-Winzeln and continue on bypass L600. Take the left turn to Winzeln, then the first right. After passing the village entrance, turn third right and you arrived at Wakol premises.
Terms and Conditions of Delivery and Payment
1. Scope of Application
1.1 The present Terms and Conditions of Delivery and Payment shall be an integral part of any and all offers and contracts with the purchaser. They shall only apply in the case of entrepreneurs within the meaning of Sections 14 and 310 of the German Civil Code [BGB].
1.2 The Terms and Conditions of Delivery and Payment shall also apply to future contracts with the purchaser insofar as they have been acknowledged by purchaser for a previous contract.
1.3 The purchaser’s general standard terms and conditions shall be excluded. They shall apply only if and insofar as we expressly acknowledge them. They shall also not apply even if we have not contradicted the purchaser’s reference to them.
1.4 The provision of deliveries and/or services shall not be regarded as approval of the purchaser’s general standard terms and conditions.
2. Offers, Conclusion of Contract
2.1 Offers shall be binding if we have issued them in writing and they do not contain any declared reservations.
2.2 If a purchase order deviates from the information in the offer, then the deviation must be reconfirmed by us.
2.3 Contracts shall be concluded based on the contents of a purchase order if we confirm the latter with the identical contents or undertake delivery directly according to the purchase order.
2.4 References to the range of applications and possible uses of our products available to the general public do not exempt the purchaser from examination of their suitability for the specific purpose intended by the purchaser. They should not be used without specific advice in the case of doubt with regard to their suitability and application.
3. Prices, Delivery, Returnable Containers, Return of Packaging
3.1 Unless otherwise agreed prices shall be based on the price list that is valid upon conclusion of contract and shall be charged to the purchaser plus the respective legally defined value added tax.
3.2 Insofar as no other handling is agreed deliveries shall be “Ex Works (EXW) (named place) Incoterms® 2010.”
3.3 We shall be entitled to make appropriate partial deliveries within a reasonable scope.
3.4 If partial deliveries have been agreed and/or the purchaser has the right to issue demand-driven call orders for ordered quantities in accordance with agreements reached with the purchaser, then the purchaser shall be obliged to accept the overall quantity agreed for the products, regardless of this handling option.
3.5 If in accordance with the agreement we make the products available to the purchaser in returnable containers, then the purchaser shall be obliged to return the containers to us at the purchaser’s own risk and expense within ninety days after acceptance of the products. The purchaser shall be responsible for damage to or loss of the containers in the purchaser’s area of risk.
3.6 We shall only take back one-way packaging if and insofar as we are obliged to do so due to contractual or statutory provisions.
4. Dates, Deadlines
4.1 Delivery dates, call dates and delivery periods shall be binding only if they have been specified through mutual consent between us and the purchaser.
4.2 Agreed dates and deadlines shall be appropriately extended at least by the duration of the impediment in cases of force majeure or the occurrence of other unforeseeable events beyond our sphere of influence and for which we may not be held responsible. This shall apply in particular in the case of strike, lockout and war to the extent that such events have a verifiable substantial impact on deliverability. If such impediments continuously persist for longer than four weeks, then each of the contracting parties shall have the right to withdraw from the contract either in part or as a whole with respect to the unfulfilled part of the contract. Any other claims shall remain unaffected.
4.3 If we are in delay, then the purchaser shall be obliged to grant us the possibility of subsequent delivery within an appropriate period before undertaking other measures in accordance with the statutory rights to which the purchaser is entitled. The regulation with regard to liability in Clause 9 shall apply to damage incurred by the purchaser due to the delay.
5. Passing of the Risk
5.1 The risk shall pass to the purchaser when the products ae kept ready for takeover at the designated place, regardless of whether partial deliveries take place or whether we have taken over arrangements for the shipment and/or the shipping charges.
5.2 If delivery is delayed due to circumstances for which the purchaser may be held responsible, then the risk shall pass to the purchaser with receipt of notification of readiness for collection / shipment.
5.3 If the purchaser claims differences in quantity or weight, then the values determined upon delivery to the carrier shall be determining.
6. Payment, Setoff
6.1 The invoice amount shall be paid without deduction within thirty days as of the date of the invoice. Payment shall be regarded as on time if we are able to dispose of the amount with value on the due date on the specified account.
6.2 In the event of delayed payment by the purchaser we shall have the right to charge a flat rate of interest on arrears in the amount of 9% above the respectively valid base interest rate. We reserve the right to assert claims for additional damage with a minimum flat rate of Euro 40.
6.3 Setoff by the purchaser shall be excluded unless the purchaser’s claims are the subject of declaratory judgment, recognized or uncontested.
6.4 In the event that we become aware of circumstances that seriously cast doubt on the solvency of the purchaser or if insolvency proceedings are instituted against the purchaser’s assets, then all of our claims against the purchaser shall become immediately due. We shall then also be entitled to only provide outstanding deliveries in return for prepayment or other security.
6.5 We reserve the right to accept bills of exchange and cheques in each individual case. They shall be accepted only on account of performance. Credit notes through bills of exchange and cheques shall be subject to receipt and with the value date on the day on which we are able to dispose of the equivalent amount. The purchaser shall be responsible for any expenses which we incur as a result.
7. Retention of Title
7.1 We reserve the right to retain title to the products delivered by us (products subject to retention of title) up to complete payment of the purchase price and payment of any other outstanding claims against the purchaser.
7.2 The purchaser shall be obliged to sufficiently secure products subject to retention of title against theft and damage at the storage location for as long as title has not passed to the purchaser.
7.3 Working and processing of the products subject to retention of title shall take place on our behalf as manufacturers within the meaning of Section 950 of the German Civil Code [BGB] without obligation on our part. The processed product shall also be considered as a product subject to retention of title. In the case of processing, combination or commixture of the product subject to retention of title with other products by the purchaser, then we shall be entitled to co-ownership of the new item in proportion to the purchase price of the product subject to retention of title to the purchase price of the other products used. Insofar as the product subject to retention of title is commixed with items that are to be regarded as the principal item, then it shall be agreed that the purchaser assigns us proportionate co-ownership of such items and safeguards the co-ownership for us.
7.4 If our title expires with processing, combination and commixture, then the purchaser shall assign us the property rights to which the purchaser is entitled in the new item in the amount of the purchase price of the product subject to retention of title. The ensuing rights of co-ownership shall be considered as an item subject to retention of title. The purchaser shall store the new item for us with due care.
7.5 The purchaser shall be entitled to resell the item subject to retention of title in the normal course of business. The purchaser shall already now assign us any claims arising out of such resale up to the amount of our claims and we shall accept such assignment.
7.6 The assignment shall be valid regardless of whether the products are resold without or after processing by the purchaser. The purchaser shall continue to be entitled to collection of the claim even after assignment. Our right to collect the claim by ourselves shall remain unaffected. However, we shall refrain from doing so as long as the purchaser meets the purchaser’s payment obligations toward us, is not in delay of payment, payment has not ceased and no request for institution of insolvency proceedings against the purchaser’s assets has been submitted.
7.7 We shall be obliged to release the collateral to which we are entitled insofar as the value of our collateral exceeds the securable claims by more than 10%.
7.8 The purchaser shall immediately notify us in the event of a pledge or any other impairment of the item subject to retention of title through third parties. The purchaser shall immediately inform the enforcement body and the judgment creditor about the fact that the item subject to retention of title is our property/joint property and/or that the rights to such have been assigned.
8. Notice of Defects, Claims Based on Defects, Period of Limitation for Claims Based on Defects
8.1 The purchaser shall be obliged to immediately examine the products in the normal course of business after delivery and to immediately report any defects discovered in writing while indicating the reasons for complaint. Complaints with regard to weight must take place in the same form within three days after delivery.
8.2 In the case of a justified notice of defects we shall provide subsequent performance in accordance with statutory provisions. Insofar as we fail to do so within a reasonable period of grace prescribed to us or if subsequent performance has failed, then the purchaser shall have the right to require reduction of the remuneration or to withdraw from the contract in the case of a breach of duty that is more than insignificant. The purchaser shall not be entitled to withdrawal but only entitled to reduction of the remuneration if the products have already been processed and are capable of being used by the purchaser as contractually stipulated.
8.3 We shall not be liable for damage incurred by the purchaser due to the fact that the purchaser employs a product for purposes which cannot be anticipated or which are not agreed. We shall also not be liable if the purchaser fails to observe technical specifications or setup recommendations which we provide for the employment of our products and damage occurs as a result.
8.4 We shall assume no responsibility if formulations prescribed to us by the purchaser result in defects or an impairment or a change in the properties of manufactured products expected by the purchaser which we are unable to determine within the scope of the production process or based on any other knowledge.
8.5 The purchaser’s claims to payment of damages due to defects shall be based on Clause 9.
8.6 The purchaser’s statutory rights of recourse in accordance with Sections 478 and 479 of the German Civil Code [BGB] due to defects in the case of sales of consumer goods and their period of limitation shall remain unaffected.
8.7 The period of limitation for claims based on defects shall amount to 12 months as of delivery. The statutory period of limitation shall apply in accordance with Section 438 Paragraph 1 No. 2 of the German Civil Code [BGB] in the event that we deliver defective products to the purchaser that lead to the defectiveness of a building. The period of limitation provided for by law shall likewise apply to claims of the purchaser due to injury to life, limb or health, violation of the German Product Liability Act, intentional breach of duty on our part or fraudulent concealment of a defect.
9. Other Liability
Any claims for damages on the part of the purchaser or claims to reimbursement of expenses asserted against us for any legal reasons whatsoever shall be excluded unless mandatory liability or a claim for the following reasons is involved: We shall be liable in accordance with statutory provisions in cases of non-contractual liability in accordance with the German Product Liability Act, in the case of intent, gross negligence, disregard of warranted characteristics and in the case of personal injuries. In the case of violation of material contractual obligations the purchaser’s claim for compensation shall be limited to typical, foreseeable damage. Statutory provisions shall apply insofar as we cause such in a deliberate or grossly negligent manner or personal injury occurs as a result.
10. Place of Performance, Place of Jurisdiction, Applicable Law
10.1 The place of performance for deliveries and services and the place of performance for payments shall be our registered place of business in Pirmasens.
10.2 The place of jurisdiction shall be the competent court for our registered place of business. At our option we may also bring action against the purchaser at the purchaser’s registered place of business.
10.3 The law prevailing in the Federal Republic of Germany shall apply. The United Nations Convention on Contracts for the International Sale of Goods (CISG) from April 11, 1980 shall be excluded.
(As of: September 1, 2014)